Glossary
Browse the IADC Lexicon alphabetically or by category. Get comprehensive definitions of drilling industry terms.
Process Of Quenching
Definition(s)
Process Of Quenching
Hardening of a ferrous alloy by austenitizing and then cooling rapidly enough so that some or all of the austenite transforms to martensite. Source: API SPEC 7-1, Specification for Rotary Drill Stem Elements, First Edition, March 2006 (Addendum April 2011). Global StandardsNon-Pressure Flank – Pin
Definition(s)
Non-Pressure Flank – Pin
Thread flank farthest from the make-up shoulder where no axial load is induced from make-up of the connection or from tensile load on the drill stem member. Source: API SPEC 7-1, Specification for Rotary Drill Stem Elements, First Edition, March 2006 (Addendum April 2011). Global StandardsNon-Pressure Flank – Box
Definition(s)
Non-Pressure Flank – Box
Thread flank closest to the make-up shoulder where no axial load is induced from make up of the connection or from tensile load on the drill stem member. Source: API SPEC 7-1, Specification for Rotary Drill Stem Elements, First Edition, March 2006 (Addendum April 2011). Global StandardsLower Kelly Valve or Kelly Cock
Definition(s)
Lower Kelly Valve or Kelly Cock
Essentially full-opening valve installed immediately below the kelly, with outside diameter equal to the tool joint outside diameter, that can be closed to remove the kelly under pressure and can be stripped in the hole for snubbing operations. Source: API SPEC 7-1, Specification for Rotary Drill Stem Elements, First Edition, March 2006 (Addendum April 2011). Global StandardsLow-Stress Steel Stamps
Definition(s)
Low-Stress Steel Stamps
Steel stamps that do not contain any sharp protrusions on the marking face. Source: API SPEC 7-1, Specification for Rotary Drill Stem Elements, First Edition, March 2006 (Addendum April 2011). Global StandardsLength Of Box Thread (LBT)
Definition(s)
Length Of Box Thread (LBT)
Length of threads in the box measured from the make-up shoulder to the intersection of the non-pressure flank and crest of the last thread with full thread depth. Source: API SPEC 7-1, Specification for Rotary Drill Stem Elements, First Edition, March 2006 (Addendum April 2011). Global StandardsH2S Trim
Definition(s)
H2S Trim
All components, except external valve body, meeting the H2S service requirements of ISO 15156-2 and ISO 15156-3. NOTE For the purposes of this provision, NACE MR0175 is equivalent to ISO 15156–2 and ISO 15156–3. Source: API SPEC 7-1, Specification for Rotary Drill Stem Elements, First Edition, March 2006 (Addendum April 2011). Global StandardsHeat, Noun
Definition(s)
Heat, Noun
Metal produced by a single cycle of a batch melting process. Source: API SPEC 7-1, Specification for Rotary Drill Stem Elements, First Edition, March 2006 (Addendum April 2011). Global StandardsGas-Tight
Definition(s)
Gas-Tight
Capable of holding gas without leaking under the specified pressure for the specified length of time. Source: API SPEC 7-1, Specification for Rotary Drill Stem Elements, First Edition, March 2006 (Addendum April 2011). Global StandardsGauge Point
Definition(s)
Gauge Point
Plane perpendicular to the thread axis in API rotary shouldered connections. NOTE The gauge point is located 15,9 mm (0.625 in) from the shoulder of the product pin. Source: API SPEC 7-1, Specification for Rotary Drill Stem Elements, First Edition, March 2006 (Addendum April 2011). Global StandardsForging, Noun 〈Product〉
Definition(s)
Forging, Noun 〈Product〉
Shaped metal part formed by the forging method. Source: API SPEC 7-1, Specification for Rotary Drill Stem Elements, First Edition, March 2006 (Addendum April 2011). Global StandardsForge, Verb 〈Hammer〉
Definition(s)
Forge, Verb 〈Hammer〉
Plastically deform metal, usually hot, into desired shapes by the use of compressive force, with or without dies. Source: API SPEC 7-1, Specification for Rotary Drill Stem Elements, First Edition, March 2006 (Addendum April 2011). Global StandardsDepth Prove-Up
Definition(s)
Depth Prove-Up
Act of grinding a narrow notch across a surface-breaking indication until the bottom of the indication is located and then measuring the depth of the indication with a depth gauge for comparison to acceptance criteria. Source: API SPEC 7-1, Specification for Rotary Drill Stem Elements, First Edition, March 2006 (Addendum April 2011). Global StandardsBending Strength Ratio (BSR)
Definition(s)
Bending Strength Ratio
The ratio of the section modulus of a rotary shouldered box at the point in the box where the pin ends when made up divided by the section modulus of the rotary shouldered pin at the last engaged thread. Source: API RP 7G, Recommended Practice for Drill Stem Design and Operating Limits, Upstream Segment, Sixteenth Edition, August 1998 (Addendum 2: September 2009). Global StandardsBending-Strength Ratio (BSR)
Ratio of the section modulus of the box thread at its last engaged thread to the pin thread at its last engaged thread. Source: API RP 7G-2, Recommended Practice for Inspection and Classification of Used Drill Stem Elements, First Edition, August 2009. Global StandardsBending Strength Ratio (BSR)
Ratio of the section modulus of a rotary shouldered box at the point in the box where the pin ends when made up, to the section modulus of the rotary shouldered pin at the last engaged thread. Source: API SPEC 7-1, Specification for Rotary Drill Stem Elements, First Edition, March 2006 (Addendum April 2011). Global StandardsBack Reflection
Definition(s)
Back Reflection
Signal received from the back surface of a surface test object. Source: API SPEC 7-1, Specification for Rotary Drill Stem Elements, First Edition, March 2006 (Addendum April 2011). Global StandardsA-Scan Display
Definition(s)
A-Scan Display
Ultrasonic instrument display in which the received signal is displayed as a vertical height or “pip” from the horizontal-sweep time trace, while the horizontal distance between two signals represents the material distance for time of travel between the two conditions causing the signals. Source: API SPEC 7-1, Specification for Rotary Drill Stem Elements, First Edition, March 2006 (Addendum April 2011). Global StandardsAmplitude
Definition(s)
Amplitude
Vertical height of the A-scan received signal, measured from base to peak or peak to peak. Source: API SPEC 7-1, Specification for Rotary Drill Stem Elements, First Edition, March 2006 (Addendum April 2011). Global StandardsPreparation
Definition(s)
Preparation
“Preparation” refers to surface preparation, joint preparation, fit-up and preheat. Source: API SPEC 6A, Specification for Wellhead and Christmas Tree Equipment, Twentieth Edition, October 2010 (Addendum November 2012). Global StandardsPreparation
“Preparation” means any commercial formulation containing one or more Active Substances including any additives. This term also includes any Active Substances generated onboard for purposes of ballast water management and any relevant chemicals formed in the ballast water management system that make use of Active Substances to comply with the Convention. Source: Resolution MEPC.169(57), revised Procedure for approval of ballast water management systems that make use of Active Substances (G9), 4 April 2008, International Maritime Organization. Regulatory GuidancePreparation
Preparation means a mixture or solution that consists of two or more substances. Source: Guidelines Regarding the Activities Regulations, Norway, updated December 2012. Regulatory GuidancePartial Overlay Equipment
Definition(s)
Partial Overlay Equipment
Equipment where some, but not all, retained fluid-wetted surfaces are either weld overlaid or weld clad with a corrosion-resistant alloy or an austenitic stainless steel to resist metal-loss corrosion. Source: API SPEC 6A, Specification for Wellhead and Christmas Tree Equipment, Twentieth Edition, October 2010 (Addendum November 2012). Global StandardsFull Overlay Equipment
Definition(s)
Full Overlay Equipment
Equipment where all retained fluid-wetted surfaces are either weld overlaid or weld clad with a corrosion-resistant alloy or an austenitic stainless steel. Source: API SPEC 6A, Specification for Wellhead and Christmas Tree Equipment, Twentieth Edition, October 2010 (Addendum November 2012). Global StandardsUSV
Definition(s)
USV
Underwater safety valve. Source: API SPEC 6A, Specification for Wellhead and Christmas Tree Equipment, Twentieth Edition, October 2010 (Addendum November 2012). Global Standards Source: API SPEC 17F, Specification for Subsea Production Control Systems, Second Edition, December 2006 (Reaffirmed April 2011). Global StandardsUSV
Underwater safety valve (see ISO 10423). Source: API SPEC 17D, Design and Operation of Subsea Production Systems—Subsea Wellhead and Tree Equipment, Upstream Segment, Second Edition May 2011 (Errata September 2011). Global StandardsSSV
Definition(s)
SSV
Surface Safety Valve. Source: ISO 16530-1:2017, Petroleum and natural gas industries — Well integrity – Part 1: Life cycle governance, First Edition, March 2017. Global Standards Source: API SPEC 6A, Specification for Wellhead and Christmas Tree Equipment, Twentieth Edition, October 2010 (Addendum November 2012). Global Standards Source: IADC UBO / MPD Glossary, December 2011. Global StandardsRL
Definition(s)
RL
Repair/remanufacture level. Source: API SPEC 6A, Specification for Wellhead and Christmas Tree Equipment, Twentieth Edition, October 2010 (Addendum November 2012). Global StandardsRMS
Definition(s)
RMS
Riser management system. Source: API Specification 16Q, Design, Selection, Operation, and Maintenance of Marine Drilling Riser Systems, Second Edition, April 2017. Global StandardsRMS
Riser management system. Source: API Specification 16Q, Design, Selection, Operation, and Maintenance of Marine Drilling Riser Systems, Second Edition, April 2017. Global StandardsRMS
System designed to document, evaluate, and diagnose the design, fabrication, operation, and maintenance history of a riser component, assembly, or system through its lifecycle. Source: API SPEC 6A, Specification for Wellhead and Christmas Tree Equipment, Twentieth Edition, October 2010 (Addendum November 2012). Global Standards Source: API SPEC 17D, Design and Operation of Subsea Production Systems—Subsea Wellhead and Tree Equipment, Upstream Segment, Second Edition May 2011 (Errata September 2011). Global Standards Source: API SPEC 17F, Specification for Subsea Production Control Systems, Second Edition, December 2006 (Reaffirmed April 2011). Global Standards Source: Deepwater Well Control Guidelines. IADC GuidelinesQTC
Definition(s)
QTC
Qualification test coupon. Source: API Specification 16A, Specification for Drill-through Equipment, Fourth Edition, April 2017. Global Standards Source: API STANDARD 16AR, Standard for Repair and Remanufacture of Drill-through Equipment, First Edition, April 2017. Global Standards Source: API SPEC 6A, Specification for Wellhead and Christmas Tree Equipment, Twentieth Edition, October 2010 (Addendum November 2012). Global Standards Source: API SPEC 16C, Specification for Choke and Kill Systems, First Edition, January 1993 (Reaffirmed 2001). Global Standards Source: API SPEC 16RCD, Specification for Drill Through Equipment—Rotating Control Devices, Upstream Segment, First Edition, February 2005. Global Standards Source: API SPEC 17D, Design and Operation of Subsea Production Systems—Subsea Wellhead and Tree Equipment, Upstream Segment, Second Edition May 2011 (Errata September 2011). Global StandardsPR
Definition(s)
PR
Performance requirement level. Source: API Specification 16A, Specification for Drill-through Equipment, Fourth Edition, April 2017. Global StandardsPR
Designation determined by the extent of testing successfully performed in accordance with minimum performance criteria identified by this specification. Source: API Specification 16A, Specification for Drill-through Equipment, Fourth Edition, April 2017. Global StandardsPR
Performance requirement. Source: API SPEC 6A, Specification for Wellhead and Christmas Tree Equipment, Twentieth Edition, October 2010 (Addendum November 2012). Global StandardsPR
Public relations. Source: Deepwater Well Control Guidelines. IADC Guidelinespr
100 kPa (0.010197 kgf/mm2, 14.5 lbf/in2)
Source: ABS Guidance Notes on Geotechnical Performance of Spudcan Foundations, January 2017. Global Standards